Viconics VRP5000 (Classic ZigBee) Installation Manual User Manual download pdf

0028-0265-04

www.viconics.com / [email protected]

Product overview

The VRP5000W1000W wireless repeater has been specically designed to be used

within a Viconics wireless ZigBee network for Viconics wireless controllers.

The repeater is intended to be a low cost additional communication component used

when some remote controllers are too far from the main mesh of the Viconics device

cluster and cannot communicate with either:

• A VWG ( Viconics Wireless Gateway )

• A JACE wireless communication card and related WirelessStatNetwork driver le that have been specically designed to

be used by the Niagara AX

powered JACE controllers.

The repeater(s) will enable the remote controller(s) to re-establish communication and act as bridge(s) to the main mesh.

The repeater(s) can be installed where most convenient such as a wall or in a suspended ceiling space if required.

VRP5000W1000W

24 VAC Powered Zigbee Repeater

For Viconics Wireless Networks Applications

(Issue Date May 3rd, 2012 – 028-0265-04)

VRP5000W1000W

Repeater

Viconics Controller(s)

Main Mesh Cluster

Remote Viconics

Controller(s) Cluster

The following documentation is available on www.viconics.com

• VWG hardware installation is available in document LIT-VWG-40-INSTALL-Exx

• VWG BACnet integration information is available in document ITG-VWG-40-BAC-Exx

• VWG information on design considerations of a wireless mesh network set-up and diagnostics is available in document

LIT-VWG-40-SETUP-Exx

• JACE2 communication card set-up, integration information and design consideration of wireless mesh networks for set-

up and diagnostics is available in document MAN-Wireless-Stat-Driver-Guide-Exx

1 2 3 4 5 6 7

Summary of Contents

Page 1 - VRP5000W1000W

0028-0265-041www.viconics.com / [email protected] overview The VRP5000W1000W wireless repeater has been specically designed to be used within

Page 2 - Installation

0028-0265-042www.viconics.com / [email protected] • Remove security screw on the bottom of repeater cover. • Open cover by pulling o

Page 3 - Controller

0028-0265-043www.viconics.com / [email protected] Initial Design And Deployment Considerations Proper design considerations need to be addresse

Page 4 - 0028-0265-04

0028-0265-044www.viconics.com / [email protected] a single controller is too far away and cannot join the main network with a single repeater, mult

Page 5

0028-0265-045www.viconics.com / [email protected] Status LED ¾ Be sure all controllers and repeaters connected to a VWG and JACE are

Page 6 - Signicance and adjustments

0028-0265-046www.viconics.com / [email protected] conguration parameter menu Conguration is done locally at the repeater.• To enter con

Page 7 - Fig.13 – Repeater dimensions

0028-0265-047www.viconics.com / [email protected]cations Repeater power requirements: 19-30 VAC 50 or 60 Hz; 2 VA Class 2Operating conditions

Comments to this Manuals

No comments

Viconics VRP5000 (Classic ZigBee) Installation Manual User Manual

Browse online or download User Manual for For Home Viconics VRP5000 (Classic ZigBee) Installation Manual. Viconics VRP5000 (Classic ZigBee) Installation Manual User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for For Home Viconics VRP5000 (Classic ZigBee) Installation Manual